What siding contractors Boston homeowners hire should handle
Siding is the part of the job you see. The part that decides whether it lasts is behind it. When we open a wall in Roslindale or on a Dorchester side street we often find several generations stacked up: the original clapboard or cedar shingle with old paint on it, sometimes a layer of asphalt or aluminum siding, then vinyl nailed over everything. Each layer hides the sheathing a little better. A siding job worth paying for deals with that before new material goes up.
The work we take on:
- Full siding replacement in fiber cement, vinyl, cedar shingle or wood clapboard
- Tear-off of old vinyl, aluminum or asphalt siding down to the original wall
- Sheathing and framing repair where water has been getting in
- Weather barrier, window and door flashing, and kick-out flashing where a roof edge meets a wall
- Corner boards, window casings, frieze boards and water tables in PVC or wood
- Siding repair: storm damage, cracked boards, rotted courses near decks and grade, failed caulk joints
- Window replacement while the walls are open, so the flashing ties together
If old shingles look like they might be cement-asbestos, we have them tested before anyone cuts or pulls them.
Boston siding by house type
Triple-deckers make up a big share of the siding work in Dorchester, South Boston, Roxbury and East Boston. They are tall, close to the neighbors, and covered with bays, porches and porch roofs. Most of the ones we see have vinyl or aluminum over the original clapboard. The hard parts are access (staging three stories up on a side yard that is four feet wide), the bay corners where water finds its way in, and the stacked porch roofs that dump water against the wall below. Window and siding contractors in Boston who have done a lot of these plan the staging and the porch ceilings before they price the job.
Victorians in Jamaica Plain, Roslindale and around Ashmont Hill are a different problem. They often have patterned cedar shingles, brackets, deep frieze boards and layered window trim. Flattening that under plain vinyl changes the house more than most owners expect. On these we usually suggest cedar or fiber cement on the walls and rebuilding the trim in PVC or wood to the original profiles.
Colonials and Capes in West Roxbury and Hyde Park are the simplest. Plain walls, clapboard, good access. Almost any material works, so the decision comes down to budget, maintenance and how much insulation you want to add.
Brick rowhouses in the South End and Back Bay have little siding, but rear ells, dormers and roof structures are often clad in wood or vinyl. Most of these sit inside historic districts, which shapes what we can install.
Fiber cement, vinyl and cedar: choosing siding for Boston weather
Fiber cement gives you the look of painted clapboard or shingle and it does not burn. The Building America Solution Center, run by the Pacific Northwest National Laboratory for the U.S. Department of Energy, places it among the claddings most likely to meet a one hour fire rating. It is also rigid and brittle. Nails over-driven near the edge of a board crack it, and those cracks let water in. The same guide recommends flashing the butt joints of lap siding instead of relying on caulk, and priming all six sides of wood and fiber cement boards. We do both. Expect to repaint fiber cement eventually, although factory finishes hold up longer than site paint.
Vinyl is the low-maintenance choice and the least expensive one. It never needs paint. It also moves with temperature, so panels have to hang loosely on their nails and lock into the course below. The Solution Center notes that some vinyl cracks when hit by a fast-moving object and that products rated for high wind use a stronger nailing hem and thicker vinyl. For vinyl siding Boston houses near the harbor or on exposed hills, we price the thicker panels. Vinyl also gets brittle in deep cold, so we schedule big vinyl jobs outside the worst weeks of winter when we can.
Cedar shingle and clapboard is what most of these houses were built with. It is repairable one piece at a time, looks right on a Victorian, and takes stain or paint. It needs that finish renewed on a schedule, and it rots where it stays wet. The federal guide puts the threshold for fungal growth at a wood moisture content around 20 percent, which is why we keep cedar off roofs and decks and give it a way to dry.
PVC trim deserves a mention because it fixes the most common failure we see: rotted wood trim at the bottom of corner boards, around sills and where porch roofs meet the wall. It does not rot, takes paint, and machines like wood. It does expand along its length in summer sun, so joints need to be fastened and glued properly.
What goes behind the siding
The Solution Center’s advice on siding starts with a blunt idea: install it assuming it will leak sometime in its life. Wind-driven rain gets past every cladding eventually. What matters is where that water goes next.
Behind the siding we install a water-resistive barrier, lapped shingle-fashion so water always runs over the layer below, with seams taped. At windows and doors the barrier ties into sill pans and head flashing. Behind lap siding, the guide recommends a small drainage gap, about 1/16 inch, which some textured house wraps provide by themselves. For wood and fiber cement on walls that take a lot of weather, a true rainscreen of furring strips speeds drying, which means less swelling and longer paint life.
Roof-wall intersections deserve their own sentence. Where a porch roof or a lower roof runs into a sidewall, water pours down the step flashing at the eave. Without kick-out flashing to turn it into the gutter, it runs straight into the wall. Federal guidance for existing homes says that where kick-out flashing is missing, the wall below the eave should be checked for damage, and where flashing is missing or failing, the siding comes off to expose at least 8 inches of wall so the flashing can be rebuilt. It also calls for leaving about 1.5 inches between the siding and the roof shingles. On Boston houses with stacked porch roofs, these spots account for a large share of the rot we cut out.
Re-siding is also the cheapest time to add insulation to the outside of the house. A U.S. Department of Energy funded study by a New Jersey Institute of Technology team looked at adding a layer of rigid insulation that also works as the air and water barrier during re-siding. It changes the depth of window and door trim, so it has to be planned, not added at the end. Our insulation and air sealing work covers the inside of the same walls.
Siding repair in Boston, and when replacement wins
Plenty of siding repair Boston homeowners ask us about is small and worth doing. Common repairs:
- A run of vinyl panels cracked by ice falling off a roof or by a ladder
- Fiber cement boards cracked at nail lines
- Cedar shingles rotted at the bottom courses next to a deck, stair or garden bed
- Open butt joints and dried-out caulk letting water behind trim
- Missing kick-out flashing, which shows up as a stained or soft patch of wall below a roof edge
Matching is the catch. Vinyl colors fade, so a new panel from the same line may not match a wall that has faced south for fifteen years. We sometimes move siding from a hidden wall to the visible one and put new panels where nobody looks.
Replacement wins when the problems stop being local: soft sheathing across several walls, wavy vinyl telegraphing an uneven wall underneath, wood siding that peels back to bare wood a year after painting, or stains and mold on the inside of exterior walls. At that point patching only moves the leak.
Covering old siding versus tearing off
One of the most common questions is whether vinyl can go over what is already there. It is allowed in many cases, and it is cheaper on day one. We usually advise against it on older Boston houses for three reasons. You cannot see or fix the sheathing. The added thickness pushes the siding past the window and door casings, which then need extensions or caps that rarely look right and often leak. And moisture that gets between the layers has a hard time drying.
Tearing off to the original wall costs more in labor and disposal, and on most houses here it is the better long-term job. If the original clapboard is in good shape and the house is in a historic district, the right answer may be to repair and paint it instead. Our exterior painting crews handle that.
Lead paint and siding work on pre-1978 homes
Most of the houses we side in Boston were built before 1978, and the original clapboard and trim almost always carry lead paint somewhere in the layers. Two sets of rules apply when someone is paid to disturb it.
The Massachusetts Department of Labor Standards says that renovation, repair or painting on a pre-1978 home must be done by a licensed lead-safe renovation contractor, licensed under 454 CMR 22.00. The EPA’s Renovation, Repair and Painting rule covers the same houses and requires certification for anyone paid to disturb paint. Its minor repair exemption stops at 20 square feet of exterior paint. A siding tear-off is far past that.
In practice that means plastic sheeting on the ground well out from the wall, closed windows, misting and careful removal instead of dry scraping, daily cleanup with HEPA vacuums, and a cleaning check before we pack up. Ask any contractor for both credentials before the job starts.
Permits, licensing and historic districts for siding in Boston
Boston Inspectional Services handles siding replacement as a Short Form permit when no structural change is involved. The City’s own example of structural work is cutting into a wall. If exterior lights, outlets or a meter have to be moved, only a contractor with a Massachusetts trade license can pull the electrical permit and do that work. Short Form work has to start within six months of the permit, and the licensed contractor must be there for the final inspection.
The Massachusetts Specialty construction supervisor license for windows, doors and siding covers siding installation and removal, plus repair of damaged window or door framing under 4 feet wide and up to 25 percent of the sheathing, on buildings under 35,000 cubic feet and one and two family homes. Anything structural beyond that needs a one and two family or unrestricted license. On an owner-occupied home with one to four units, the company also has to be registered as a Home Improvement Contractor, and any job over $1,000 needs a written contract.
Boston has 10 local historic districts. Visible siding changes there, including a switch from wood to another material, can need commission approval before the permit, and Inspectional Services does not request that approval for you. We put together the material samples and photos the commissions ask for and build the review into the schedule.
What drives the cost of new siding
We do not publish a price per square foot, because two Boston houses with the same wall area can price very differently. The main factors:
- The number of existing layers to remove, and whether lead-safe containment is needed
- How much sheathing and framing turns up rotten once the wall is open
- Height and access: staging a triple-decker over a narrow side yard costs more than a ranch with open lawn
- Material: vinyl, fiber cement, cedar shingle or wood clapboard
- Trim detail: corner boards, window and door casings, bays, brackets and frieze boards
- Added insulation or rainscreen furring, which changes every window and door detail
- Historic district review, or permits for electrical changes on the walls
Comparing siding companies: Boston questions to ask
Ask each of the siding installers Boston friends recommend the same questions, in writing:
- Which Construction Supervisor License does the person running the job hold, and what is the number?
- What is the Home Improvement Contractor registration number? You can look it up on mass.gov.
- Is the company licensed for lead-safe renovation in Massachusetts and certified by the EPA?
- What exactly goes behind the siding: which weather barrier, how windows are flashed, whether kick-out flashing is included?
- How is rotten sheathing priced? A per-sheet price in the contract avoids arguments later.
- Who pulls the permit? It should be the contractor.
A siding contractor in Boston who answers those clearly is usually one you can work with. We hand over the same answers on request.
Where we work
We work in every Boston neighborhood, from Charlestown and East Boston to West Roxbury and Hyde Park. For homes outside the city, see our siding contractors across Massachusetts page. When siding comes with new windows or a new roof edge, we coordinate it with our window replacement, roofing and gutters and trim crews. To set up a visit, use our contact page.
How a siding project works with us
Call or request an estimate
Tell us what you need and roughly when.
On-site visit
We look at the space, measure and talk through options.
Written estimate
A clear scope, price and schedule, line by line.
Permits & build
We file permits, do the work, pass inspections and walk it through with you.
Siding across Massachusetts
See our siding contractors massachusetts page for work outside Boston.
- Siding Installation Amherst MA: New Walls for Houses and Rental Buildings
- Vinyl Siding Andover MA: Replacement, Insulated Panels and Town Review
- Siding Contractors Arlington MA: Hearings, Lead Paint and Permits
- Vinyl Siding Ashland MA: Choosing Material by House and Building
- Siding Attleboro MA: Replacing Siding on a City of Mixed Housing
- Siding Contractors Brookline MA: Partial Demolition, Districts and Permits
- Burlington MA Vinyl Siding: Re-Siding the Houses Route 128 Built
- Cambridge MA Siding Contractor: Clapboard, Shingles and Fiber Cement on Old Houses
- Vinyl Siding Fitchburg MA: Re-Siding the City's Older Houses
- Vinyl Siding Installation Hopkinton MA: New Houses and the Old Center
- Siding Contractors Milton MA: Re-Siding Houses Built Before the War
- Vinyl Siding Natick MA: Which Houses Can Switch, and How
- Siding Newton MA: The 50 Percent Rule, Historic Districts and Permits
- Vinyl Siding Installation Norfolk MA: Re-Siding a Town of Detached Houses
- Vinyl Siding Plymouth MA: Installation and Replacement Done Right
- Vinyl Siding Installation Randolph MA: Permits, Prep and Panel Choices
- Vinyl Siding Somerville MA: Re-siding Old Two and Three-Family Houses
- Vinyl Siding Woburn MA: Permits, Fees and What Each Era of House Needs
- Siding Worcester MA: Replacement and Repair on Older City Houses
- Vinyl Siding Installation Wrentham MA: Two Kinds of Houses, Two Kinds of Jobs
Siding questions
Is fiber cement or vinyl siding better for a Boston house?
Neither wins everywhere. Fiber cement looks like painted wood, handles fire well and suits Victorians and Colonials where trim detail matters, but it is brittle and needs paint over time. Vinyl costs less and never needs paint, but some panels crack when struck and it changes the look of an older house more. We price both when either would work.
Do I need a permit to replace siding in Boston?
Yes. The City treats siding replacement as Short Form permit work when nothing structural changes. If the job cuts into a wall, it moves to a different permit. If exterior lights or outlets have to be moved, a licensed electrician pulls an electrical permit.
Can new vinyl siding go over my existing siding?
It can be done, but we rarely recommend it on older Boston homes. Covering old siding hides rot and missing flashing, thickens the wall so window and door trim no longer line up, and can trap moisture between layers. Tearing off to the original wall lets us fix the sheathing and install a continuous weather barrier.
Will new siding make my house warmer?
Siding alone does little. The gains come from what goes on with it, mainly air sealing and, where the trim details allow, a layer of rigid insulation outside the sheathing. Research funded by the U.S. Department of Energy looked at exactly this, adding insulation that also serves as the air and water barrier during re-siding.
What should I do about lead paint under old siding?
If the house was built before 1978, assume the original clapboard and trim carry lead paint. Hire a contractor licensed for lead-safe renovation in Massachusetts and certified under the EPA's renovation rule. A full tear-off goes far beyond the EPA's 20 square foot exterior threshold, so containment and cleanup rules apply.
Does vinyl siding need maintenance?
Less than any other option, but not none. Wash it once in a while, keep sprinklers and mulch off the bottom course, check that panels are still locked together after a windstorm, and keep caulk joints at trim in good shape. Damaged panels can be swapped individually if you have matching stock.
Sources
Facts on this page were last checked against these sources on November 14, 2026.
- City of Boston, Install or replace siding (accessed 2026-11-14)
- City of Boston, How to get a Short Form permit (accessed 2026-11-14)
- Mass.gov, Learn about different Construction Supervisor Licenses (accessed 2026-11-14)
- Mass.gov, HIC contractor resources (Do I need to register as a Home Improvement Contractor?) (accessed 2026-11-14)
- Mass.gov, Department of Labor Standards, Lead-safe renovation for contractors (accessed 2026-11-14)
- U.S. EPA, Renovation, Repair and Painting Program for contractors (accessed 2026-11-14)
- Building America Solution Center (PNNL), Moisture, impact, fire and pest resistant exterior siding (accessed 2026-11-14)
- Building America Solution Center (PNNL), Flashing roof-wall intersections in existing homes (accessed 2026-11-14)
- Building America Solution Center, Re-Side Right, a systems approach to high performance re-siding projects (NJIT, 2023) (accessed 2026-11-14)
- City of Boston, Office of Historic Preservation 2025 year in review (accessed 2026-11-14)