What commercial roofing contractors Massachusetts owners hire us to do
Our commercial work is low-slope roofing on buildings where people live or work underneath. That includes apartment buildings and condominiums, mixed-use blocks with stores at street level, small office buildings, retail strips, and churches and schools with flat sections. The work splits into four parts:
- Full replacement, with tear-off to the deck, deck repair, new tapered insulation and a new membrane
- Recover, where the code and the existing roof allow a new system over the old one
- Commercial roof repair: open seams, punctures, failed flashing at walls, curbs and penetrations, and leaks at drains and scuppers
- Maintenance programs with scheduled inspections, drain cleaning and written reports for owners and managers
Pitched roofs on houses are a different trade with different materials. Those are covered on our residential roofing page.
The membranes: TPO, EPDM, PVC and modified bitumen
Nearly every commercial roof we touch in the Boston area is one of four systems. Each has a place.
TPO is a thermoplastic single-ply membrane. Its seams are joined with hot air, so the seam becomes one piece of material rather than a glued lap. Most TPO is white or light colored, which keeps the roof surface cooler in summer. It is a common choice for replacement on apartment and office buildings.
PVC is also a heat-welded thermoplastic. It costs more than TPO, and it holds up better where the roof sees grease, oils or chemicals, which is why it is the usual answer over a restaurant kitchen exhaust or a lab.
EPDM is synthetic rubber, usually black, joined with seam tape and adhesives. It tolerates movement and cold well, and it is easy to patch years later. Many older Boston-area flat roofs are EPDM, and a sound EPDM roof can often be repaired rather than replaced.
Modified bitumen is asphalt reinforced with polymers, installed in two or more plies. It can be heat-applied, cold-applied with adhesive, or self-adhered. The multi-ply build makes it tough under foot traffic, which suits roofs with a lot of mechanical equipment and service visits. On occupied wood-frame buildings we lean toward cold-applied or self-adhered sheets instead of open-flame torching.
What matters as much as the membrane is how it is attached. Membranes can be mechanically fastened, fully adhered or ballasted, and the right method depends on the deck, the wind exposure of the roof edge, and what the manufacturer will warrant.
Tapered insulation and drainage
Water that sits on a roof finds every weakness in it. Ponding speeds up membrane wear, loads the deck, and freezes into ice around drains in winter. On older buildings in Boston, Cambridge and Somerville, the deck itself has often sagged between supports over the decades, so water collects in the middle of each bay.
The building code sets the minimum. The 2021 International Building Code, which the Massachusetts 10th edition is built on, requires a design slope of at least 1/4 unit vertical in 12 units horizontal, a 2 percent slope, for single-ply and modified bitumen roofs. On a flat structural deck, that slope has to come from the insulation.
Tapered insulation is cut in sloped panels laid out like a map, with crickets and saddles that push water around curbs and toward drains and scuppers. We design the taper layout before pricing, because it controls the insulation thickness at the high points, which in turn controls the height of the roof edge, flashing at walls and door thresholds onto the roof. On some buildings adding a drain or a scupper is cheaper than building enough taper to reach the existing ones.
Energy code insulation on commercial reroofs
Massachusetts uses the 2021 International Energy Conservation Code with state amendments as its base energy code, found in 780 CMR Chapter 13 for commercial buildings. Cities and towns that opt in follow DOER’s Stretch or Specialized code instead, which for commercial buildings is 225 CMR 23.
For reroofing, the key rule in the 2021 IECC is the roof replacement section. Where the existing roof assembly is part of the building’s thermal envelope and the insulation is entirely above the roof deck, a roof replacement has to meet the current insulation requirements. The same section says the roof insulation R-value can never be reduced, and the assembly’s U-factor can never be increased, as part of the replacement.
What that means in practice:
- A full tear-off on a typical membrane roof with insulation above the deck usually requires bringing insulation up to today’s level, which is often much thicker than what comes off
- The extra thickness raises the roof surface, so curbs, wall flashings, door sills and roof hatches may need to be raised
- Where insulation is below the deck or in a ceiling, this section does not apply the same way, and other parts of the code govern
- Which version of the code applies depends on the city or town, so we confirm the required R-value with the building department before we finalize a price
Insulation thickness is often the biggest single change between what an owner expects and what the permit requires, and it is better to know before the board votes.
Recover or full replacement
A recover installs a new roof over the existing one without tearing off. It costs less and creates far less disruption, and sometimes it is the right call. The 2021 IBC sets clear limits, though. A recover is not allowed when the existing roof or covering is water soaked or deteriorated past the point of being a sound base, when the existing covering is slate, clay, cement or asbestos-cement tile, or when the roof already has two or more layers of any roof covering.
That is why we start with core cuts and moisture readings. Insulation that has been wet for years is heavy, has lost much of its value, and keeps feeding moisture into the new roof. When cores show a mostly dry roof with a few wet areas, we may recommend removing and replacing the wet sections and recovering the rest. When the readings show widespread water, a full tear-off is the only honest recommendation.
The code also bars reinstalling rusted or damaged flashing, metal edging, drain outlets and counterflashing during reroofing, so plan on new metal at the edges either way.
Commercial roofing in Boston on occupied buildings
The City of Boston is direct about who can do roof work on larger residential buildings. For a three-family or larger building, including one floor of a triple-decker or a multi-unit condo, you must hire a contractor. Owners of those buildings cannot do it themselves.
Licensing depends on building size. The Massachusetts Specialty roof covering license covers roof covering work, including replacing up to 25 percent of the sheathing, on buildings under 35,000 cubic feet. Many apartment and commercial buildings are larger than that, and those fall outside the construction supervisor license categories, so different supervision rules apply. We confirm the requirements for your building at the permit stage.
Boston commercial roofing jobs are mostly logistics:
- Crane or hoist picks for materials, with any street permits the city requires for the crane and dumpster
- Tear-off in sections that are dried in by the end of each day, so an afternoon storm does not reach the top floor units
- Protected building entrances and a clear path for residents under the work area
- Advance notice to tenants about noise, odors from adhesives, and any rooftop unit shutdowns
- Coordination with HVAC contractors when rooftop units have to be disconnected and lifted
- A single point of contact for the property manager, with daily photos if the board wants them
On commercial buildings open to the public, roof repair and replacement on its own is exempt from the Architectural Access Board’s partial-compliance trigger in 521 CMR 3.00 unless the work costs more than $500,000. That cost still counts toward the 30 percent of building value threshold if the roof is part of a larger renovation. When roofing is one piece of a bigger project, our commercial construction group plans the whole job.
Old roofs and asbestos
Older roofing materials can contain asbestos, and MassDEP lists roofing among the building materials where it may be found. If a test is positive, Massachusetts requires notice to MassDEP and the Department of Labor Standards at least ten working days before abatement or removal begins. MassDEP also notes that intact asbestos-containing asphaltic roofing removed according to its rules may be disposed of in a permitted solid waste landfill. We sample suspect materials during the initial survey so a positive result changes the schedule on paper, not on the roof.
Inspections and maintenance for property managers
Most of the commercial roof repair Boston managers call us for starts small. A drain clogged with leaves, a seam that opened at a corner, a pitch pocket that dried out, a satellite dish bolted through the membrane by a tenant’s installer. Caught in spring, each of these is a short repair. Found after a winter of leaks, it can mean wet insulation over a whole bay.
NRCA technical guidance recommends inspecting roof systems at least twice a year, preferably in spring and fall, and again after severe weather. A good inspection program covers:
- Drains, strainers, scuppers and gutters cleared and checked for flow
- Seams and laps probed, especially at corners and around curbs
- Flashing at walls, parapets, rooftop units, pipes and hatches
- Signs of ponding, blistering, or membrane shrinkage pulling at the edges
- Damage from foot traffic and other trades, including new penetrations nobody reported
- Photos and a short written report with repairs priced individually
Keep those reports. Manufacturer warranties on commercial systems vary widely in length and coverage, and most come with conditions about maintenance, notice of leaks and who may cut into the roof. Read the warranty terms before signing a contract and ask who is responsible for each one.
How to compare commercial roofing contractors Boston boards are considering
Condo boards and managers often get three bids that describe three different roofs. To compare them fairly:
- Ask what each bidder found in core cuts or moisture testing, and whether the price is for recover or full tear-off.
- Compare insulation: type, total thickness, R-value, and whether it meets the energy code your town follows.
- Ask for the tapered layout, showing where water goes and what happens at each drain.
- Compare flashing heights, edge metal and how each rooftop unit and penetration is handled.
- Check the attachment method and whether the manufacturer will issue the warranty described in the bid.
- Ask for a certificate of insurance sent by the insurer, and who will pull the permit.
- For small condo buildings of up to four units where owners live, check Home Improvement Contractor registration too, since state HIC rules cover owner-occupied homes of one to four units.
What affects the cost of a commercial roof
We do not publish prices per square foot, because they would mislead more than help. These are the factors that drive a commercial roofing estimate in Massachusetts:
- Tear-off versus recover, and how much wet insulation and damaged deck turns up
- The insulation thickness required by the energy code for a full replacement
- Taper design, crickets, and any new drains or scuppers
- Membrane choice and attachment method
- Number of rooftop units, curbs, hatches, skylights and pipe penetrations
- Parapet height, edge metal and wall flashing
- Access: crane time, street permits, and work around occupied units or businesses
- Asbestos testing and, if needed, abatement
Where we work
We handle the commercial roofing Boston, MA buildings need, and work in the cities and towns around it, from Quincy and Dorchester to Cambridge, Somerville, Chelsea and the North Shore. See our Massachusetts service area for the full list, or contact us to schedule a roof survey with core cuts and a written report.
How a commercial roofing project works with us
Call or request an estimate
Tell us what you need and roughly when.
On-site visit
We look at the space, measure and talk through options.
Written estimate
A clear scope, price and schedule, line by line.
Permits & build
We file permits, do the work, pass inspections and walk it through with you.
Commercial Roofing questions
Can a new membrane go over our existing flat roof?
Sometimes. The building code allows a recover only when the existing roof is dry and sound enough to serve as a base, and not when there are already two or more roof coverings on it. We take core cuts and moisture readings before recommending one. Wet insulation has to come off either way.
Does a commercial reroof have to meet the energy code?
When it is a full replacement and the insulation sits entirely above the deck, yes. The 2021 IECC, which Massachusetts adopts with amendments as its base energy code, requires those roofs to meet current insulation levels and never allows the R-value to drop. Communities on the state's Stretch or Specialized codes follow DOER's version, so we confirm the target with the building department before pricing.
TPO, EPDM, PVC or modified bitumen, which is best?
It depends on the building. TPO and PVC have heat-welded seams and light-colored surfaces, PVC holds up better around restaurant exhaust and grease, EPDM handles movement well and is easy to repair, and modified bitumen gives a tough multi-ply surface for roofs with heavy foot traffic. We recommend one after looking at the deck, the drainage, the rooftop equipment and how the roof is used.
How often should a property manager have the roof inspected?
At least twice a year, in spring and fall, and again after any major storm. That follows NRCA guidance. Regular inspections catch clogged drains, open seams and damaged flashing early, and a written record helps if you ever file a warranty or insurance claim.
Can you replace the roof while residents and tenants stay in the building?
Yes. Almost every job we do is on an occupied building. We tear off and dry in the same section the same day, keep entrances protected, schedule crane picks and noisy work with the manager, and give residents notice before each phase.
Could the old roof contain asbestos?
On older buildings, it can. MassDEP lists roofing among the building materials that may contain asbestos. If testing finds it, removal has to be noticed to MassDEP and the Department of Labor Standards at least ten working days before work starts, so we test early.
Sources
Facts on this page were last checked against these sources on November 14, 2026.
- International Code Council, 2021 International Building Code, Chapter 15 Roof assemblies and rooftop structures (accessed 2026-11-14)
- International Code Council, 2021 International Energy Conservation Code, Chapter 5 CE Existing buildings (C503.2.1 Roof replacement) (accessed 2026-11-14)
- Mass.gov, Massachusetts building energy codes (DOER) (accessed 2026-11-14)
- Mass.gov, Tenth edition of the MA State Building Code 780 (accessed 2026-11-14)
- City of Boston, Repair a roof (accessed 2026-11-14)
- Mass.gov, Learn about different Construction Supervisor Licenses (accessed 2026-11-14)
- Mass.gov, 521 CMR 3.00 Jurisdiction (Architectural Access Board) (accessed 2026-11-14)
- Mass.gov, MassDEP asbestos, construction and demolition notifications (accessed 2026-11-14)
- Professional Roofing (NRCA), Tech Today, October 2013 (inspect roof systems twice a year) (accessed 2026-11-14)