What Boston gutters have to handle
A gutter system has one job: collect the water coming off the roof and put it somewhere harmless. The amount is bigger than most people picture. The Building America Solution Center, run by the Pacific Northwest National Laboratory for the U.S. Department of Energy, points out that a few inches of rain on an ordinary roof can produce several thousand gallons of runoff. Without gutters, or with gutters that dump it at the corner of the house, that water soaks the soil along the foundation and works its way into basements.
Boston adds its own problems. Lots are small, so the side of one house is often a few feet from the next, and there is little room to carry water away. Old maples and oaks fill gutters in October and again with seeds in spring. Roofs here also hold snow for weeks in a hard winter, and gutters take the weight of the ice that forms at the eave.
The work we take on:
- New aluminum gutters roll-formed on site to one continuous length per run, so there are no joints except at corners
- Half-round and copper gutters for older houses
- Relining and repair of built-in wood gutters (Yankee gutters) at the eave
- Downspouts, extensions, splash blocks and solid drain lines to daylight
- Leaf guards and screens
- Fascia, soffit, rake boards, frieze and corner trim in PVC or wood
- Kick-out flashing where a roof edge dies into a wall
Gutters on Boston houses, by type
On Colonials, Capes and most suburban-style houses in West Roxbury, Hyde Park and Roslindale, the standard is a 5 or 6 inch K-style aluminum gutter with rectangular downspouts. Formed on site from a coil, each run comes off the truck as one piece cut to length, which removes the seams that leak first on sectional gutters.
Triple-deckers mostly have flat or low-slope roofs behind a parapet or a cornice. Water leaves through scuppers or interior drains into tall leaders running down the side or back of the building. The gutters on these buildings are often on the porch roofs, which take all the water from the front of the house. Undersized porch gutters on a triple-decker are one of the most common sources of rotted porch ceilings we see.
Victorians and older houses in Jamaica Plain, Dorchester and Brighton often have built-in gutters: a wooden trough framed into the roof edge and hidden behind a cornice, originally lined with metal. When the lining fails, water goes straight into the cornice and the wall. The fix is either a new lining (copper, or a membrane under metal) or, where the owner and any historic commission agree, roofing over the trough and hanging an external gutter.
Rowhouses in the South End, Back Bay and Charlestown are similar to triple-deckers at the main roof, with built-in gutters or box gutters at the front cornice and leaders on the rear.
Copper gutters in Boston
Copper gutters in Boston show up on Back Bay and Beacon Hill townhouses, on Victorian bays, and on houses where the owner wants them to last and never be painted. Half-round copper with round downspouts is the traditional look. Copper costs much more than aluminum, so we usually suggest it where it shows or where it ties into existing copper: bay roofs, dormer flashing, built-in gutter linings.
Copper has rules. It needs copper hangers and fasteners, because steel and aluminum in contact with copper corrode quickly in the presence of water. Runoff from copper stains lighter materials below it, and galvanized or aluminum parts downstream of copper corrode faster. Seams are soldered, not caulked. When we are asked for copper gutters Boston ma suburbs see on older Colonials, we look at what is already on the house before recommending a switch.
Sizing, pitch and downspout placement
Most gutter failures start at the design stage. The Building America guidance gives simple numbers we use as a starting point:
- Allow 1 square inch of downspout cross-section for every 100 square feet of roof area
- Place downspouts at least 20 feet and no more than 50 feet apart
- Slope gutters at least 1/16 inch per foot toward the downspouts
- Use bigger gutters and more leaders where heavy rain and wind are common
Gutters come in 4, 5 and 6 inch sizes, and a bigger channel only helps if there are enough downspouts to empty it. On a steep Victorian roof, water comes off fast enough to shoot over a small gutter, so we size up and move the gutter to catch it. Where two roof planes meet in a valley above a gutter, a splash guard keeps the concentrated flow from jumping the front edge.
Pitch is a balance. Too little and water sits, freezes and grows mosquitoes. Too much and a long run drops visibly across the front of the house. On long runs we pitch from the middle to downspouts at both ends.
Where downspouts should drain in Boston
This is where gutters and basements meet. The Building America guidance says roof runoff should be carried away from the foundation, with downspouts ending at least 5 feet from it or feeding an underground catchment at least 10 feet away. Buried lateral pipe should be solid, not perforated, and pitched away from the house. Gutter drains should never tie into the perforated foundation drain around the footing, which would deliver roof water to the very place you are trying to keep dry.
The Boston Water and Sewer Commission adds a city rule. Some older Boston downspouts were piped into the sewer. The Commission says downspouts that discharge to the sewer system violate Massachusetts General Laws, the Massachusetts Plumbing Code and its own Sewer Use Regulations, and that improperly connected downspouts need to be disconnected and redirected to the yard or another landscaped area. Its brochure explains why: in heavy rain, stormwater in the sanitary sewer can overload it and contribute to sewer backups and flooding.
On a tight city lot we work with what is there: a downspout extension across a walkway with a hinged section, a splash block and regrading, or a solid line under a path to a planting bed or the far side of a driveway. If your basement takes water every spring, drainage outside is the first thing we look at before talking about our basement waterproofing work.
Winter, ice and gutters boston ma homeowners worry about
Snow and ice are hard on gutters here. A gutter full of ice weighs a lot, and spikes driven through the face of the gutter into old fascia pull out after a few winters. We hang gutters with hidden hangers screwed into the rafter tails or a solid fascia, spaced closer together on the north side of the house where ice lingers.
The Building America guidance is clear that gutters do not cause ice dams. Ice dams form when heat leaking from the house melts snow on the upper roof and it refreezes at the colder eave. The same guidance notes that gutters can fill with snow that freezes into an ice dam that is already forming, and that screen-type leaf guards help cold-climate gutters drain instead of holding water that freezes. The lasting fix for ice dams is in the attic, which our roofing page covers.
A drip edge under the first course of shingles, lapped into the back of the gutter, keeps meltwater that does get past the edge from running behind the gutter and into the fascia.
Fascia, soffit and exterior trim repair
Bad gutters and missing flashing leave a trail of rotten wood. The most common repairs we make:
- Fascia boards rotted behind the gutter, usually from overflow or a missing drip edge
- Soffits stained or sagging below a leaking built-in gutter
- Rake boards and returns split at the corners where water sits
- Window sills and casings rotted under a dripping gutter seam
- Bottom ends of corner boards rotted where they meet a porch roof or deck
- Porch ceilings and beams damaged by an undersized porch gutter
When we replace fascia and trim, the choice is usually between primed wood and cellular PVC. Wood is cheaper, easy to match to existing profiles and takes paint well, but it rots if it stays wet. PVC does not rot or absorb water and holds paint well, which makes it the better choice close to roofs, decks and gutters. It does move with heat along its length, so long boards need to be fastened and glued at the joints.
Soffits carry air into the attic on many houses. When we replace them we keep or add vented panels where the attic needs intake air, and screen them against insects and birds.
Kick-out flashing belongs in this list too. Where a lower roof or a porch roof ends against a wall, a kick-out at the bottom of the step flashing turns the water into the gutter. Federal guidance on flashing in existing homes says that where kick-out flashing is missing, the wall below should be checked for damage, and where the flashing has failed, siding comes off to expose at least 8 inches of wall so it can be rebuilt. If the siding there is ready to go too, our siding crew handles it at the same time.
Lead paint on old trim
On a Boston house built before 1978, assume the trim has lead paint somewhere under the newer coats. Scraping fascia or prying off old rakes and soffits disturbs it.
The EPA’s Renovation, Repair and Painting rule covers paid work that disturbs paint in housing built before 1978 and requires certified firms. Its minor repair exemption ends at 20 square feet of exterior paint, and a full fascia and soffit replacement on one side of a house can exceed that quickly. The Massachusetts Department of Labor Standards requires a licensed lead-safe renovation contractor for renovation, repair or painting on pre-1978 homes. We lay plastic on the ground below the work, mist rather than dry scrape, bag debris at the end of each day and clean up with HEPA equipment. When trim is being repaired rather than replaced, our exterior painting crew finishes it under the same rules.
Cleaning and gutter guards
Clean gutters at least once a year, and twice under big trees: late fall after the leaves drop and late spring after the seeds. Flush each downspout with a hose and make sure water comes out the bottom. A downspout that clogs at the elbow fills the gutter in the next storm and overflows onto the fascia.
Guards help, with limits. Screen and micro-mesh guards keep out leaves and maple seeds and let the gutter drain in winter. Pine needles and shingle grit still collect on top. Solid hood-style covers can shoot water past the gutter in heavy rain on steep roofs. Whatever guard goes on, it should be removable for cleaning.
What moves the price of gutters and trim work
We do not post a price per foot, because the same length of gutter costs very different amounts to install on a ranch and on a triple-decker. The factors:
- Material: aluminum, copper, or relining a built-in gutter
- Height and access, including staging on narrow side yards
- How much fascia, soffit and rake board is rotten behind the old gutters
- Number of downspouts and how far the water has to be carried from the house
- Lead-safe containment on painted trim
- Guards, heat cable or other additions
How to hire for gutters boston crews install
A few questions sort out gutter contractors quickly:
- Will you check the fascia and drip edge behind the old gutters, and how is rotten wood priced?
- How will the gutters be sized and pitched, and how many downspouts will there be?
- Where will each downspout drain?
- What hangers will you use and how far apart?
- Are you licensed for lead-safe renovation in Massachusetts and certified by the EPA, if trim paint will be disturbed?
- If I live in this one to four unit home, what is your Home Improvement Contractor registration number? Massachusetts requires registration for that work and a written contract for jobs over $1,000.
Where we work
We install and repair gutters and trim in every Boston neighborhood, from Charlestown and East Boston to West Roxbury and Hyde Park, and in towns around the city. See our Massachusetts service area for the rest of the state. To book a look at your gutters, use our contact page.
How a gutters & exterior trim project works with us
Call or request an estimate
Tell us what you need and roughly when.
On-site visit
We look at the space, measure and talk through options.
Written estimate
A clear scope, price and schedule, line by line.
Permits & build
We file permits, do the work, pass inspections and walk it through with you.
Gutters & Exterior Trim questions
Should gutters be replaced when I get a new roof?
Not automatically. If the gutters are the right size, pitched toward the downspouts and firmly attached, they can come down and go back up. Replace them if they are undersized, leaking at the seams, pulling off the fascia, or if the fascia behind them is rotten. A new roof is the easiest time to fix the fascia and add a drip edge.
Are copper gutters worth it in Boston?
On the right house, yes. Copper lasts a long time, needs no paint, and matches the copper bays, flashing and built-in gutters on many older Boston houses. It costs much more than aluminum and has to be kept away from steel fasteners and aluminum parts to avoid corrosion. On a vinyl-sided Cape it rarely makes sense.
Where should my downspouts drain?
Away from the house and into the yard, not into the sewer. Building America guidance recommends ending downspouts at least 5 feet from the foundation, and the Boston Water and Sewer Commission says downspouts connected to the sewer must be disconnected. On tight city lots we use extensions, splash blocks or a solid pipe to a better spot.
Do gutters cause ice dams?
No. Ice dams come from heat loss melting snow on the roof. Federal guidance does note that gutters can fill with snow that freezes into an existing ice dam, so strong hangers and good attic insulation matter more here than in milder places.
Do gutter guards work?
Screen-type guards keep out leaves and seeds and help gutters drain in winter instead of holding water that freezes. They do not end maintenance. Pine needles and roof grit still collect on top, and guards should come off easily for cleaning. Under big oaks and maples they usually pay off.
Why does my fascia keep rotting?
Usually because water gets behind the gutter. Common causes are a missing drip edge, a gutter hung too low, overflow from a clogged or undersized gutter, and ice backing up at the eave. Replacing the board without fixing the cause just resets the clock. We fix both and often switch to PVC fascia.
Sources
Facts on this page were last checked against these sources on November 14, 2026.
- Building America Solution Center (PNNL), Gutters and downspouts (accessed 2026-11-14)
- Building America Solution Center (PNNL), Flashing roof-wall intersections in existing homes (accessed 2026-11-14)
- Boston Water and Sewer Commission, Downspout disconnection (2022) (accessed 2026-11-14)
- U.S. EPA, Renovation, Repair and Painting Program for contractors (accessed 2026-11-14)
- Mass.gov, Department of Labor Standards, Lead-safe renovation for contractors (accessed 2026-11-14)
- Mass.gov, HIC contractor resources (Do I need to register as a Home Improvement Contractor?) (accessed 2026-11-14)
- Building America Solution Center (PNNL), Moisture, impact, fire and pest resistant exterior siding (accessed 2026-11-14)