Masonry Contractors Boston, MA: Brick, Stone, Chimneys and Concrete

Masonry contractors Boston, MA property owners call usually get the same first question about an old brick wall, which is whether it needs repointing or a full rebuild. Most of the time the honest answer is neither, at least not yet. We repoint brick with mortar matched to the wall, rebuild chimneys, repair rubble and brick foundations, and set granite steps, block retaining walls and concrete walks across the city.

The masonry work we take on

Boston was built out of brick, puddingstone, granite and fieldstone, and most of it is still standing because someone kept the joints tight. Our crews spend most of their time on a short list of jobs:

  • Repointing brick and stone walls, from a single failed pier to a full rowhouse elevation
  • Chimney work: new crowns, rebuilt tops, full rebuilds from the roofline, and flashing coordinated with the roofer
  • Foundation repair on brick, rubble stone and block foundations, including repointing below grade and new parging
  • Granite steps and landings reset on new bases, and cast concrete stoops rebuilt where the old ones have cracked through
  • Concrete walkways, slabs, small driveways and the concrete repair Boston sidewalk edges and stairs seem to need every spring
  • Stone and block retaining walls, including rebuilding the leaning ones behind triple-deckers in Dorchester and Roslindale

If a job is mostly about water in the basement, we usually pair it with our basement waterproofing crew, because pointing a foundation wall from inside rarely fixes a drainage problem outside.

What masonry contractors Boston, MA owners should ask first

Before anyone mixes mortar, find out why the wall failed. The National Park Service makes the same point in Preservation Brief 2, its guide to repointing historic masonry: repointing will not cure damage caused by something else. A gutter dumping onto a wall, a roof leak at a parapet, a downspout that empties at the foundation, or settlement under one corner will chew through new mortar as fast as the old.

So our first visit is mostly looking. We check where the worst joints are, because the pattern tells a story. Eroded mortar under a window sill points to a failed sill or missing drip. Washed-out joints in a vertical stripe usually mean a gutter or leader problem. Cracks that step diagonally through the joints suggest movement, which needs a different conversation than routine pointing. White salt bloom on the inside of a basement wall means water is moving through it.

Then we tell you what we would fix first, what can wait a few years, and which part of the problem is not masonry at all.

Brick repointing with the right mortar

This is where older Boston buildings get hurt most often. A lot of brick in the South End, Back Bay, Charlestown and Beacon Hill was laid in soft lime mortar, and much of the brick itself is softer than modern brick. When someone repoints that wall with a hard Portland cement mix, the wall loses its weak link. Preservation Brief 2 explains why that matters. Masonry walls move with heat, cold and moisture, and the stress should be taken up by the mortar, which can be replaced, rather than by the brick, which cannot. Mortar that is stronger and less permeable than the brick traps moisture and pushes the damage into the face of the brick. The result is the spalled, flaking brick you can see on plenty of Boston facades.

The Park Service guidance sets two rules we follow on every older building:

  • New mortar has to be softer and more vapor permeable than the brick or stone it sits between.
  • New mortar has to be as soft and as permeable as the historic mortar, or softer.

In practice that usually means a lime-rich mix. The brief notes that mortar from roughly 1873 to 1930 can be anything from pure lime and sand to various lime and cement blends, so we look at the existing mortar before we pick a mix. The brief also warns against bagged masonry cement on historic buildings, because it tends to produce high-strength mortar.

How the old mortar comes out matters as much as what goes back in. The brief calls for raking joints to a depth of 2 to 2 1/2 times the joint width, which on most brick means about 1/2 to 1 inch. It also says power saws on thin brick joints almost always chip the brick edges, and that mechanical tools should never be used on the vertical head joints. We cut thin joints by hand. On wide horizontal joints in hard 20th century mortar, a skilled mason can use a grinder carefully and finish with a chisel.

Color and texture come next. We match new mortar to the unweathered mortar inside the joint, not the dirty surface, and we tool the joint to the original profile. For larger projects we build a small test panel, around 3 feet square as the brief suggests, so you can approve the look before we start the whole wall. New mortar will read slightly brighter for a while. Staining it to match is generally a bad idea, according to the same guidance, and we let it weather in.

Chimneys and the freeze-thaw problem

Chimneys take the worst of a Boston winter. They stick up above the roof with no shelter, get wet on all four sides, and then freeze. Water that soaks into a crumbling joint or a cracked crown expands as it freezes, opens the crack a little wider, and lets in more water at the next thaw. A few seasons of that and the top courses loosen.

Most chimney work we do falls into three levels:

  • Crown and cap. A cracked mortar wash at the top lets water straight into the stack. We replace it with a properly shaped crown that sheds water past the brick face, and add a cap where flues allow it.
  • Top rebuild. When the upper courses are loose or spalled, we take the chimney down to sound brick, usually somewhere near the roofline, and relay it with matching brick and appropriate mortar.
  • Full rebuild or removal. Unused chimneys on some houses are better taken down below the roof and capped, which removes a leak point. That is a decision for you, and on a visible chimney in a historic district it may need review.

We coordinate flashing with the roofer, or with our own roofing crew, because a new chimney with old flashing still leaks. Flue liners for heating appliances are a separate specialty, and when what we see on the roof points that way, we will tell you to have the flue inspected.

Foundations, parging and basement walls

Many Boston houses sit on rubble stone or brick foundations that were never meant to keep water out completely. They do need sound joints to carry the house. Masonry repair Boston homeowners ask us for here includes repointing open joints from inside and out, rebuilding small sections where stones have shifted, and parging the exposed exterior face with a breathable coat.

We match foundation mortar to the old stone or brick for the same reason we do it above grade. A rigid cement patch on a lime-mortared rubble wall tends to pop off within a few winters and can push moisture into the house elsewhere.

When a foundation shows active movement, such as wide or growing cracks, bulging, or doors upstairs suddenly binding, we stop and bring in a structural engineer before quoting.

Granite steps, concrete stoops and walkways

Granite steps are everywhere in Boston, and they last almost forever if the base under them holds. Most failures we see are a settled lower tread, a step that rocks, or a stoop pulling away from the house. We lift the granite, rebuild the base, reset the pieces level with a slight pitch to drain, and point the joints.

Cast concrete stoops are a different story. Once a concrete stair is cracked through and rust stains show at the edges, the steel inside is corroding, and patching is short-lived. We break it out and pour a new one, with a mix and finish chosen for freeze-thaw exposure and salt.

For walkways, small slabs and driveway aprons, the work is mostly about the base and the drainage. We dig out soft material, compact a gravel base, set control joints so cracking happens where we choose, and slope the surface away from the house. Patios and outdoor rooms are covered with our decks and patios team.

Retaining walls behind Boston yards

Hilly neighborhoods like Roxbury, Mission Hill, Roslindale and parts of Dorchester have old retaining walls holding up backyards, driveways and sometimes a neighbor’s garage. Most were built without drainage. Water collects behind them, freezes, and pushes the wall out a little each year.

Rebuilding a wall properly means taking it down, digging out the soil behind it, adding drainage stone and a way for water to escape, and rebuilding with stone or segmental block on a proper footing. Massachusetts treats taller walls differently. The state’s guidance for home improvement work says retaining walls and freestanding masonry walls need a building permit and a construction supervisor license once they are taller than 4 feet. Walls of any real height, or walls holding up a driveway or structure, also get an engineer’s design from us before we price them.

Permits, licenses and historic districts in Boston

Massachusetts sorts masonry work by what it is attached to. The state’s guidance chart for home improvement work lists masonry related to a building as needing a construction supervisor license, Home Improvement Contractor registration on owner-occupied homes, and a building permit. Landscape masonry and patios generally need none of those, as long as there is no public safety issue.

The license is specific. The Specialty masonry Construction Supervisor License covers construction, alteration, repair and demolition of masonry that needs a permit, on buildings under 35,000 cubic feet, one and two family homes and agricultural buildings, and on walls under 10 feet from footing to top. Larger buildings fall outside that license, so on a big apartment block or commercial building the supervision and design requirements change.

In Boston, minor repairs that do not change structure or use go through Inspectional Services as a Short Form permit, and the licensed contractor has to be on site for the final inspection. If the building is in one of Boston’s 10 local historic districts, such as the Back Bay Architectural District, the Historic Beacon Hill District or the South End Landmark District, visible exterior work can need commission approval first. Inspectional Services will not request that approval for you, so we prepare mortar samples, photos and a description of the method for the commission and build that time into the schedule.

Commercial masonry restoration in MA

We also work on mixed-use buildings, small apartment buildings and storefronts. The masonry methods do not change, but the paperwork does. On a building open to the public, the Massachusetts Architectural Access Board regulation, 521 CMR 3.00, lists repointing and masonry repair among the alterations that do not trigger its partial-compliance requirements unless the work costs more than $500,000 or involves an entrance or toilet room. That exemption is narrower than it sounds. If all work on the building over a 36 month period adds up to 30 percent or more of the building’s assessed value, the whole building has to comply, and the exempt work counts toward that total. Masonry that is part of a larger renovation is planned with our commercial construction group.

How to compare a Boston masonry contractor

A few checks separate the masons who understand old buildings from the ones who own a grinder:

  1. Ask what mortar they plan to use and why. A good answer mentions the existing mortar, the softness of the brick, and lime. “Type S, same as always” on 1880s brick is a warning sign.
  2. Ask how they will remove the old mortar from the head joints. The answer should be hand tools.
  3. Ask for the construction supervisor license number of the person running the job, and Home Improvement Contractor registration if you live in a one to four unit home. Look both up on mass.gov.
  4. For work over $1,000 on your home, get a written contract. Massachusetts requires one with home improvement contractors.
  5. Ask who pulls the permit and who handles historic commission review, if your street needs it.
  6. Look at a job they did three or more years ago. Fresh pointing always looks good. Pointing that has been through a few winters tells you more.

What drives masonry costs

We do not quote by the brick from a photo, and we would be skeptical of anyone who does. These are the things that move a masonry estimate in Boston:

  • Access and staging. A ground floor foundation wall is one price, a four story rowhouse facade on a narrow street with a sidewalk permit is another
  • How deep and how widespread the failed mortar is, and whether we are spot repointing or doing a whole elevation
  • Hand raking of thin joints, which is slower than grinding and worth it on soft brick
  • Mortar matching, test panels and any historic commission review
  • Brick or stone replacement, especially when matching salvaged brick is needed
  • Hidden conditions, like a chimney that turns out to be loose below the roofline
  • Engineering for retaining walls and anything structural

Preservation Brief 2 also suggests unit prices alongside the base bid on repointing work, so a contract can adjust fairly if the footage of bad joints changes once scaffolding goes up. We write our masonry contracts that way on larger jobs.

Where we work

We work in every Boston neighborhood and in the surrounding cities and towns. Rowhouses in the South End and Back Bay, triple-deckers in Dorchester and Southie, and stone walls in West Roxbury all come across our desk. For other services we offer statewide, see our Massachusetts service area, or contact us to set up a site visit.

How a masonry & concrete project works with us

  1. Call or request an estimate

    Tell us what you need and roughly when.

  2. On-site visit

    We look at the space, measure and talk through options.

  3. Written estimate

    A clear scope, price and schedule, line by line.

  4. Permits & build

    We file permits, do the work, pass inspections and walk it through with you.

Masonry & Concrete across Massachusetts

Masonry & Concrete questions

How do I know if my brick needs repointing?

Look for mortar that is recessed well behind the brick face, crumbling when you scratch it with a key, or cracked along a line. Damp interior plaster and loose bricks are other signs. Spot repointing of the bad areas is usually enough. Whole elevations are rarely needed at once.

Can you repoint old brick with regular Portland cement mortar?

Not on soft, older brick. National Park Service Preservation Brief 2 explains that hard, impermeable mortar forces stress and moisture into the bricks, which then crack and spall. Repointing mortar should be softer and more permeable than the brick and no harder than the historic mortar, which on most older Boston buildings means a lime-rich mix.

Do I need a permit for masonry work in Boston?

Masonry that is part of a building, such as a chimney, foundation or brick wall, generally needs a permit and a licensed construction supervisor. Landscape masonry and patios generally do not. Retaining walls and freestanding walls over 4 feet need both a permit and a CSL. Minor repairs that do not change structure or use go through Boston's Short Form permit.

Repair or rebuild my chimney?

If the bricks are sound and the problem is the crown, the flashing or the top few courses, repair it. If bricks are spalling from the inside, the stack leans, or mortar is gone deep into the joints for several feet, rebuilding from the roofline up is usually the better use of money. We show you photos from the roof before you decide.

Is repointing covered by Massachusetts accessibility rules on a commercial building?

On its own, usually not. The Architectural Access Board regulation lists repointing and masonry repair among the alterations that do not trigger its partial-compliance rule unless the work tops $500,000 or touches an entrance or toilet room. All work, including that exempt work, still counts toward the 30 percent of building value threshold for full compliance.

When is the best time of year for brick work?

Late April through October in most years. The Park Service guidance calls for wall temperatures between 40 and 95 degrees F so the mortar neither freezes nor dries too fast. We schedule south and west walls for mornings in summer and keep fresh joints damp and shaded.

Sources

Facts on this page were last checked against these sources on November 14, 2026.

  1. National Park Service, Preservation Brief 2, Repointing Mortar Joints in Historic Masonry Buildings (accessed 2026-11-14)
  2. Mass.gov, HIC contractor resources (What work requires an HIC, CSL, or building permit?) (accessed 2026-11-14)
  3. Mass.gov, Learn about different Construction Supervisor Licenses (accessed 2026-11-14)
  4. City of Boston, How to get a Short Form permit (accessed 2026-11-14)
  5. City of Boston, Office of Historic Preservation 2025 year in review (accessed 2026-11-14)
  6. Mass.gov, 521 CMR 3.00 Jurisdiction (Architectural Access Board) (accessed 2026-11-14)

Planning a masonry & concrete project?

Free, no-pressure estimates in Boston and across Massachusetts.